Lineage 2 Macro Bot (Lineage 2 human)

First you will need to download a program called actool. It is 5mb and you can download it through
the following link:

http://www.actool.net/files/actoolinstall_462.exe


After you download it run it to install actool on your computer and open actool.

There are 2 macro bots provided below. Each one has is different and should be used
in different situations.


1. The first is a simple bot that I use to get to level 20 as fast as possible. It will target a certain mob
and attack it. This bot will not sit down or rest between kills so be careful not to fight mob that are
too higher or you will die fast.

a) First open actool and copy bot1 into actool.

b) Second run lineage 2 and find a open area with lots of spawns that you can kill easily.

c) You will need to set up you toolbar as follows: Attack in slot1, Skill attack or special attack in
slot2 and pickup item in slot3. If you don t have a special attack yet just leave slot2 blank.

d) Find a mob(monster) that has a lot of spawns around the area and remember the EXACT name of
the mob.

e) Alt tab out of the game and bring actool up. You will see a line in bot1 that says Keys /Target
[name here] Put the name of the mob you want to kill where it says name here . So if you want to
kill goblin graverobbers the line would look like Keys /Target [goblin graverobbers] . Then save
bot1 and run it.

f) If everything was done right lineage 2 will open and start attacking the nearest goblin
graverobber. A few seconds after the mob is killed your character will target the next nearest
goblin graverobber and attack it. Important: To stop the bot alt tab out of the game a select macro
> stop macro in actool. DO NOT push any buttons or click the mouse while the bot is running or it
will mess up the bot.

2. The second bot is used when you only want to kill one spawn and then sit and rest for a few
seconds. This is used in dungeons and places with spawns that don t move very much.

a) First open actool and copy bot2 into actool.


b) Second run lineage 2 and find the place you want to camp a spawn.

c) You will need to set up you toolbar as follows: Attack in slot1, Skill attack or special attack in
slot2, pickup item in slot3, target next in slot4 and sit/stand in slot5.

d) Find a mob(monster) that you want to camp and sit very close to its spawn point.

e) Alt tab out of the game and bring actool up. You will not need to enter the mobs name anywhere
because this bot will just target the nearest mob and attack it. Run the macro

f) If everything was done right lineage 2 will open and start attacking the nearest mob. A few
seconds after the mob is killed your character will sit down and rest for 30 seconds then get up and
attack the nearest mob again. Important: To stop the bot alt tab out of the game a select macro >
stop macro in actool.

Important: When bot2 is running you CAN push buttons and click the mouse. Doing things such as
checking your inventory or moving a little closer to the mob WILL NOT mess up the bot.


Good Luck and Thanks for buying our bot macros




Bot 1

The following code needs to be copied into actool.


SetActiveWindow Lineage II
Constants
Attack = {F1}
Pickup = {F3}
Skill = {F2}
End
delay 5 sec
While 1=1
Loop 8
Keydown $Attack 250
Delay 250
Keydown $Skill 250
Delay 250
Keydown $Pickup 250
Delay 250
end
keys {return}
Keys /Target [name here]
keys {return}
end




Bot 2

The following code needs to be copied into actool.


SetActiveWindow Lineage II
Constants
Attack = {F1}
Pickup = {F3}
Target = {F4}
Skill = {F2}
Sit = {F5}
End
delay 5 sec
While 1=1
Loop 14
Keydown $Attack 250
Delay 250
Keydown $Skill 250
Delay 250
Keydown $Pickup 250
Delay 250
Keydown $Target 250
Delay 250
end
Keydown $Sit 250
Delay 250
end

If all else fails try The MMORPG Exchange L2 Adena . MMORPG-Exchange has supplied me for years and they have great customer service and 24/7 instant delivery.
Lineage 2 Adena.

This entry was posted in L2 Adena Lineage. Bookmark the permalink.

6 Responses to Lineage 2 Macro Bot (Lineage 2 human)

  1. Dude says:

    I dont see a line where bot1 that says Keys /Target ;/

  2. Scout017 says:

    Mhm , i could be lucky , because this bot is running very good on xp professional , but not on my Laptop with vista and i tryed to find vista codec but failed.

  3. Scout017 says:

    Oh anyone knows website where to get these needed vista codec for ac tools ?

  4. Dark says:

    Almost at the end “Keys /target”

    (:

  5. wrak says:

    For Vista/7 issue try run AC Tool as Admin (Right click and Run as administrator)

Leave a Reply

Your email address will not be published. Required fields are marked *